Skip to main content

Living Room Series Rabbit Home by Ware Mfg. Assembly Instructions

If you have purchased a Living Room Series Rabbit Home by Ware Mfg. and have misplaced the assembly instructions this post should help get back on track. If you have had your Rabbit Home for a while and you need replacement parts we can help critter-cages.com carries parts for this item. If you do not see a part you need listed give us a call 310 832-9981 M-F 10 am to 6 pm Pacific Time or drop us an email at orderdesk@critter-cages.com and we will check on availability.  We also stock lots of toys, treats and equipment for all your Furry Friends.

Parts
Replacement Plastic Base 900479
Replacement Wire Floor Grid 900478
Replacement Ramp 900497/901347
Replacement Shelf 900493
Replacement Caster Set 900492
Replacement Leg Extensions 900468
Replacement Hardware Pack 900457
Replacement Roof Panel 900477 
Replacement Side Panel 900456 
Replacement Food Dish 900469

Putting your Living Room Series Rabbit Home Together

Before you start assembling your new Living Room Series Rabbit Home it is a good idea to lay out all the parts and make sure they are all there.  The graphic below will help you check.  Assembly is easy if you follow the instructions, no tools are needed. If you find there are parts missing contact the manufacturer's customer service department at 800 295-2243.

Step 1

Using the Hex Wrench, attach the back panel to the right side panel using two of the bolts. Make sure the support tabs on the top rail are open to the inside.
Attach the front panel in the same way, making sure the door opens out.
TIP: Do Not tighten bolts fully uintil all the panels are in place.


 Step 2

Tighten all of the bolts after making sure that all the support tabs on the top of the back and front rails are open towards the inside.

 Step 3

Attach the roof panel by sliding the right rear lower wire extension under the support tabs and into the hole on the side panel.
Slide the left end of the lower wire extension under the open tabs and into the hole in the left side panel.
Attach side panel with four more hex bolts and tighten all.


 Step 4

The top roof panel should swing freely and close by latching into the front open tabs on the front top frame bar.











Step 5

Lay the cage on its side and attach the four casters to the leg posts.
Place the floor grate into the top of the plastic tray. Swing the locking tab on the front of the lower frame bar up while sliding the grate and tray into the channels of the lower side frame bars.


Step 6

Attach the plastic ramp to the bottom side of the plastic shelf by snapping them into the plastic clips.
Place the assembled shelves and ramps in the cage through the door. Attach the shelf and ramp assembly to the 7th wire up from the bottom on the left side of the cage.









Step 7

After completing the above steps your Living Room Series Home should be ready for move in. Place the food dish on the shelf, add the cage bedding of your choice and a water bottle, your pet is now ready
to enjoy its new home.  

For Other Small Critter, Chicken, and Poultry Products

If you are looking for other things for your Fury Friends, make sure you check out our website at http://critter-cages.com . We offer a large selection of cages, welded wire and supplies for you furry, four legged and feathered Critters. Whether you are looking for Chicken Runs, Cages for your Critters, Feeders or even chicken wire, take a look at our large selection of Poultry and other products for your Critters.

Comments

  1. Living Room Series Rabbit Home by Ware Mfg. Assembly Instructions best guide ever. This has all the help that ones need in the living room. Great share.

    ReplyDelete
  2. Small house extensions can make a real difference to how you're able to use your living space. Even if your budget is small, a well thought-through addition to your house can make a tiny dining area more usable or create extra space for a home office. Loft Conversion High Peak

    ReplyDelete
  3. In many ways the bedroom is the most important space in the house. It is instead in how the space articulates a sense of harmony, in its suitability for sleep and those slow, quiet hours at night and in the morning, that has become the focus of bedroom design. Kitchen & bedroom respray specialists

    ReplyDelete
  4. Not only is the kitchen vitally important because it contains the appliances and tools necessary to prepare any kind of meal, but it is also one of the most important spaces for storage, seating, and communication. Without the kitchen, the home would likely feel empty and confused, without a direction.Bedroom Design Barnby Dun

    ReplyDelete
  5. Our kitchen cabinet painting is a highly detailed refinishing process where we properly prepare the kitchen cabinet doors, drawers and boxes to be painted with a factory finish that is beautifully smooth and durable. Spraying Services Wales

    ReplyDelete
  6. Microwaves have sorted out some technique for directing different cooking frameworks, as I said, they can grill or plan steamed food. The best portable microwave uses configuration setting progress to allow you to have these shocking results, ie speed and straightforwardness in food blueprint. A contraption will have protected dividers that will hold the waves inside and heat the food.

    ReplyDelete

Post a Comment

Popular posts from this blog

You & Me Rat Manor by Petco Assembly Instructions

If you have purchased a You & Me Rat Manor , from Petco or others and can't find your instructions or you would like to see how easily it goes together before you buy.  Just keep reading as we lay out how to put your You & Me Rat Manor together. If you are actually looking for replacement parts for this Cage, we have them available at Critter-Cages.com Assembling the You & Me Rat Manor One of the best things about this cage is that no tools are needed for assembly. Make sure you have all the parts as listed:   Step 1 Place the Wire Cage on a flat surface and carefully unfold all of the panels as shown in the image .  Step 2 Connect the bi-folded front cage panel (the one with the doorway) to the left bi-folded side panel as shown. The "J" shaped wire hooks are specially designed to hook onto the side panel again to create a woven connection joint.  Step 3 Next connect the bi-folded back panel to the left side panel by atta

Grreat Choice® Deluxe Playground Cat Tree Assembly Instructions

If you have purchased a Grreat Choice® Deluxe Playground Cat Tree from PetsMart and have misplaced the assembly instructions this post should help get back on track. If you have had your Cat Tree for a while and it is looking a bit ratty. If you need to replace parts we can help critter-cages.com carries parts for this item. If you do not see a part you need listed give us a call 310 832-9981 M-F 10 am to 6 pm Pacific Time or drop us an email at orderdesk@critter-cages.com and we will check on availability.  We also stock lots of toys, treats and equipment for all your furry feline friends and other critters to! Parts Replacement 11" (H) Post WA 901798 Replacement 4" (I) Post with Screw WA 901799 Replacement 8" (J) Post WA 901800 Replacement 15.5" (K) Post WA 901801 Replacement 7" (L) Post WA 901802 Replacement 15.5" (M) Post with Screw WA 901803 Replacement 23" (N) Post with Screw WA 901804 Replacement Hardware Pack WA 901790   Put

All Living Things Rabbit Hutch Assembly Instructions

 If you have purchased an All Living Things Rabbit Hutch from PetsMart and have misplaced the assembly instructions this post should help get back on track. If you have had your cage for a while and need to replace parts we can help critter-cages.com carries parts for this cage. If you do not see a part you need listed give us a call 310 832-9981 M-F 10 am to 6 pm Pacific Time or drop us an email at orderdesk@critter-cages.com and we will check on availability.  We also stock lots of toys, treats and equipment for all your critters. Putting your All Living Things Rabbit Hutch Together Before you start assembling your new All Living Things Rabbit Hutch it is a good idea to lay out all the parts and make sure they are all there.  The graphic below will help you check.  Assembly is easy if you follow the instructions, the only tool needed to assemble this Hutch is a Phillips screwdriver. If you find there are parts missing contact the manufacturer's customer service depart