Spin City Series Health Club Assembly Instructions

If you have purchased a Spin City Health Club Habitat, from us or others and can't find your instructions or you would like to see how easily it goes together before you buy. Spin City are great for smaller Critters like Hamsters, Gerbils, Mice and other similar sized Critters. The Run Ball comes complete with a Critter Cyclometer which allows you to keep track of just how far your Critter has run in a given time period.  Just keep reading as we lay out how to put your Spin City together.
If you are actually looking for replacement parts for this Hutch, we may have them available at Critter-Cages.com

Replacement Blue Top Roof Panel 900670
Replacement Cyclometer 901103 & 901087
Replacement Slide Bottom 900674 & 901100
Replacement Slide Top 900673 & 901099
Replacement Run Ball Left Side 900676 & 901102
Replacement Run Ball Right Side 900675 & 901101

Putting your Spin City Health Club Together

Before you start assembling your new Spin City Health Club it is a good idea to lay out all the parts and make sure they are all there.  The graphic below will help you check.  Assembly is easy if you follow the instructions,no tools are needed for assembly.

If you find there are parts missing contact the manufacturer's customer service department (Ware Mfg.) at 800 295-2243. 

Step 1

Join front and back wire panels by slightly bending inward so that the wire tabs on one panel hook and hold the other panel.

 Step 2

Place the assembled wire panels down into the plastic base. Make sure the wires are secure into the groove that runs around the inside of the base.

Step 3

Attach the two connector clips to the 4th wire up from the bottom, with the plastic loops holding the front and back wire panels. The tab should then lock securely to the base.

 Step 4

Snap the two side sections together by inserting the tabs on the bottom section into the slots on the top section. Press the tabs on the slide top into the slots on the opening of the bottom of the cage top.

 Step 5
Connect assembled cage top onto the assembled wire panels by presssing gently until it snaps into place.

Step 6

Insert wheel pin into the teeter totter/ball support. Slide wheel pin guide into slot on the right side of the cage top so the pin is facing in.

Step 7

Connect the two halves of the Run Ball together and twist to lock

Step 8

1) Place the ball into the opening on the cage top, putting the wheel pin guide into the small hole on the closed side of the run ball.

2) Attach the teeter/ball support to the run ball by snapping the pin into the opening on the open side of the ball. Press the support down in place on the cage top.

3) Place teeter totter onto the teeter totter/ball support, positioning the pins in the middle of the teeter totter into the holes on each side of the support, so that it moves up and down.

Step 9

Place the Critter Cyclometer in place in the slot on the front of the Spin City. Snap the water bottle holder to the cage wire and attach the water bottle so that the sipper is inside the cage in a spot that your critter can easily reach. Place the food dish anywhere in the cage.

The Critter Cyclometer will automatically count laps as your critter runs in the ball. Press the Reset button to reset the count to zero. To change the batteries, remove the Critter Cyclometer from the slot on the front of the cage to access the battery panel on the back.

Your Spin City Health Club is Now Ready for You Critters.

 

For Other Small Critter, Chicken, and Poultry Products

If you are looking for other things for your Fury Friends, make sure you check out our website at http://critter-cages.com . We offer a large selection of cages, welded wire and supplies for you furry, four legged and feathered Critters. Whether you are looking for Chicken Runs, Cages for your Critters, Feeders or even chicken wire, take a look at our large selection of Poultry and other products for your Critters.